Buku Logwiritsa Ntchito Ma Model 650E, 1000E, ndi 1250E

CHITSANZO                                                   SERIAL NO.                                          TSIKU

KULUMIKIZANA KWA DZIKO

Yesani kukana kuchokera ku pulagi ya pulagi yapadziko lapansi kupita ku thupi la maginito .... ohm

KUKHALA KWA ELECTRICAL

Megger kuchokera ku coil kupita ku thupi la maginito

MIN/MAX SUPPLY VOLTAGE YES

Pa 260v: Pre-clamp.... full-clamp.... release

Pa 200v: Pre-clamp .... kumasulidwa

Pre-clamp.... full clamp.... release

INTERLOCK SEQUENCE

Ndi mphamvu yoyatsa, kukoka HANDLE, kenako dinani batani la START.

Onetsetsani kuti makina OSATI akugwira ntchito

KUYATSA/KUZImitsa ANGELO

Kusuntha kwa Bending Beam kuti muyambitse kugunda kwathunthu,

kuyeza pansi pa mtengo wopindika.(4 mm mpaka 6 mm) mm

Sinthani kusuntha kwa makina ozimitsa.Yezerani mobwerera

kuyambira 90 °.(Ziyenera kukhala mkati mwa 15° + 5°) deg

ANGLE SALE

Kuwerenga m'mphepete mwa Chizindikiro pamene mtengo wopindika wayikidwa

mpaka 90 ° ndi lalikulu la injiniya.(min 89° , max 91°) deg

MAGNET BODY

Kuwongoka kwa pamwamba, motsatira mzati wakutsogolo

(kutembenuka kwakukulu = 0.5 mm)Imm

Kutsika pamwamba, kudutsa mitengo

(kupatuka kwakukulu = 0.1 mm) mm

KUPITA MALO

Kuwongoka kwa malo ogwirira ntchito (kupotoka kwakukulu = 0.25 mm)

Kuyanjanitsa kwa bar yowonjezera (kupotoka kwakukulu = 0.25 mm)[Zindikirani:Yesani kuwongoka ndi kulondola kwenikweni.]

MAIN CAMPBAR

Kuwongoka kwa m'mphepete (kutembenuka kwakukulu = 0.25 mm) Kutalika kwa chonyamulira (ndi mipira yonyamulira m'mizere) (mphindi 3 mm) Mipira yonyamulira imatha kupindika ndi pamwamba Ndi zowongolera zoyikidwa paⁿ1ⁿndi mtengo wopindika pa 90 °

ndi m'mphepetekufananaku, ndindi mmkuchokera, mtengo Ndi chipika chopindika pa 90 °, clampbar ingasinthidwe patsogolokukhudzandi kumbuyo2 mm

AMAHENGA

Yang'anani mafuta pa shafts.ndi ma block blocks

Onetsetsani kuti mahinji amazungulira 180 ° momasuka komanso bwino

Onani hingezikhomodo ayitembenuzani.ndipo zayikidwa

Kodi mtedza wosungirako watsekedwa?

KUPITA AMAYESA

(Kupindika kwakukulu mpaka 90 °, pamagetsi ocheperako.)

Chitsulo choyesera chidutswa makulidwe

Kukula kwa milomo

mm, Bend kutalika

mm, Bend radius

Kufanana kwa bend angle (kutembenuka kwakukulu = 2 °)

LABELS

Yang'anani kumveka bwino, kumamatira ku makina ndi kugwirizanitsa koyenera.

Nameplate & seri No

Machenjezo amagetsi

Chenjezo la Clampbar

Sinthani zilembo

Tepi yachitetezo pamiyendo yakutsogolo 

MALIZA

Onani ukhondo, kumasuka ku dzimbiri, zilema etc

ZIZINDIKIRO

Zosonkhanitsidwa & Kuyesedwa.

Kufufuza kwa QA

NTCHITO YOYENERA

CHENJEZO

Foda yachitsulo ya Jdc bend sheet imatha kukakamiza matani angapo (onani MFUNDO).Ili ndi cholumikizira ndi manja awiri kuti zithandizire kuonetsetsa kuti zala sizingagwire mosadziwa pansi pa clampbar pakagwiritsidwa ntchito ma electro-magnetic clamping.

Komabe,ndikofunikira kwambiri kuti wogwiritsa ntchito mmodzi yekha agwiritse ntchito makinawo panthawi imodzi.Ndizowopsa kuti munthu m'modzi alowetse chogwiriracho ndikugwira zotchingira pomwe wina akugwiritsa ntchito masiwichi!

KUPITA KWABWINO KWAMBIRI

Onetsetsani kuti mphamvu ILI WOYAMBA potulutsa magetsi ndipo chotchingira chachitali chonse chayikidwa pamakina pomwe mipira yake yonyamulira ili m'malo olowera kumapeto kulikonse.

1.Adjust kwa workpiece makulidwepozungulira ma eccentric adjusters kumapeto kwa clampbar.Kwezani mtengo wopindika mpaka 90 ° ndikuwonetsetsa kuti ikufanana ndi m'mphepete mwa clampbar - ngati kuli kofunikira sinthaninso zonyamulira eccentric.
(Kuti mupeze zotsatira zabwino, kusiyana pakati pa m'mphepete mwa clampbar ndi pamwamba pa mtengo wopindika uyenera kukhala wokulirapo pang'ono kuposa makulidwe achitsulo opindika.)

2.Ikani chogwirira ntchitokenako pendekera kutsogolo kwa clampbar pansi ndikuyanjanitsa mzere wopindika mpaka m'mphepete.
3.Dinani ndikugwira batani la START.Izi zikugwiranso ntchito pre-clamping.

4.Ndi dzanja lina kukoka pa chogwirira.Kutsekereza kwathunthu tsopano kwagwiritsidwa ntchito mokhazikika ndipo batani la START liyenera kutulutsidwa.Pitirizani kugwada mpaka ngodya yofunikira ifike.
5.Mtsinje wopindika ukhoza kutembenuzidwa pafupifupi 10 ° mpaka 15 ° kuti atenge kupanikizika kuchoka pa workpiece kuti ayang'ane mbali yopindika.Kubwereranso ndi kupitirira 15 ° kumangozimitsa makinawo ndikutulutsa ntchitoyo.
CHENJEZO

• Kupewa chiopsezo chowononga m'mphepete mwa clampbar kapena kupindika pamwamba pa maginito,osayika zinthu zing'onozing'ono pansi pa clampbar.Utali wopendekeka wocheperako pogwiritsa ntchito clampbar yokhazikika ndi 15 mm, kupatula ngati chogwiriracho chili choonda kwambiri kapena chofewa.
• Mphamvu yothina ya maginito imakhala yochepa pakatentha.Chifukwa chake kuti mupeze magwiridwe antchito abwino kwambirigwiritsani ntchito clamping kwa nthawi yayitali kuposa momwe ikufunikakuchita benda.

MPHAMVU KUNENGA(Chowonjezera chosafunikira)

MALANGIZO OGWIRITSA NTCHITO

Kumeta ubweya wa mphamvu (zochokera ku Makita Model JS 1660) zimapereka njira yodulira zitsulo zachitsulo m'njira yakuti kupotoza kochepa kwambiri kumasiyidwa mu workpiece.Izi ndizotheka chifukwa chometa ubweya chimachotsa zinyalala, pafupifupi mamilimita 4 m'lifupi, ndipo zokhota zambiri zomwe zimachitika pakumeta zingwe zimapita mumzerewu.Kuti mugwiritse ntchito ndi Jdcbend kumeta ubweya wa ubweya wapangidwa ndi kalozera wapadera wa maginito.

Kumeta ubweya kumagwira ntchito bwino kuphatikiza ndi Jdcbend Sheetmetal Foda;Jdcbend imapereka njira zonse zogwirira ntchito yokhazikika pamene ikudulidwa komanso njira yoyendetsera chida kuti kudula kowongoka kwambiri kutheke.Kudula kwautali uliwonse kumatha kugwiridwa ndichitsulo mpaka 1.6 mm wandiweyani kapena aluminiyumu mpaka 2 mm wandiweyani.

Kuti mugwiritse ntchito chida choyamba ikani chogwirira ntchito cha sheetmetal pansi pa clampbar ya Jdcbend ndikuyiyika kuti mzere wodulira ukhale ndendende.] mmkutsogolo kwa m'mphepete mwa Bend Beam.

Kusintha kosintha komwe kumatchedwa "NORMAL / AUX CLAMP,, kudzapezeka pafupi ndi chosinthira chachikulu cha ON/OFF. Sinthani izi kupita ku AUX CLAMP kuti mugwire mwamphamvu chogwiriracho.

Ikani chometa kumapeto kudzanja lamanja la Jdcbend ndikuwonetsetsa kuti cholozera maginito chimalowa kutsogolo kwa Bending Beam.Yambani kukameta ubweya wa mphamvu ndikukankhira mofanana mpaka kudula kutsirizika.

Ndemanga:

1. Kuti zigwire bwino ntchito, tsambalo liyenera kusinthidwa kuti ligwirizane ndi makulidwe azinthu zodulidwa.Chonde werengani malangizo a Makita operekedwa ndi shear ya JS1660.
2. Ngati Shear sadula momasuka onetsetsani kuti masambawo ndi akuthwa.

PINDA MILOMO

PINDA MILOMO (HEM)

Njira yomwe imagwiritsidwa ntchito popinda milomo imadalira makulidwe ake komanso kumlingo wina, kutalika kwake ndi m'lifupi.

Zopangira Zochepa (mpaka 0.8 mm)

1.Pitirizani ngati mukupindika mwachizolowezi koma pitirizani kupindika momwe mungathere (135 °).
2.Chotsani clampbar ndikusiya chogwirira ntchito pamakina koma musunthire kumbuyo pafupifupi 10 mm.Tsopano tembenuzirani mtengo wopindika kuti mupanikizike mlomo.(Kutsekereza sikuyenera kugwiritsidwa ntchito).[Zindikirani: Osayesa kupanga milomo yopapatiza pazinthu zokhuthala].

3.Ndi zogwirira ntchito zopyapyala, ndi/kapena pomwe milomo sipang'ono kwambiri, kusalala kokwanira kumatha kutheka potsatira ndi maginito clamping kokha:

M'mphepete

KUPANGA M'mphepete

Mphepete mwazitsulo zimapangidwa ndi kukulunga chogwirira ntchito mozungulira chitsulo chozungulira kapena chitoliro chokhala ndi mipanda.

1.Ikani workpiece, clampbar ndi rolling bar monga momwe zasonyezedwera.
a) Onetsetsani kuti clampbar sidutsa nsonga yakutsogolo ya makinawo pa "a" chifukwa izi zitha kulola kuti maginito azitha kudumpha ndikugudubuza kotero kuti kukangana kumakhala kofooka kwambiri.

b) Onetsetsani kuti chopukusira chagona pazitsulo zakutsogolo za ma chine (“b”) osati kupitilira mbali ya aluminiyamu pamwamba.

c) Cholinga cha clanipbar ndikupereka njira ya maginito ("c") kulowa mu bar yozungulira.

2.Mangani chogwiriracho momwe mungathere ndikuyikanso momwe zikuwonekera.

 

3.Bwerezani sitepe 2 ngati mukufunikira.

MAYESERO CHIPATA

MALANGIZO OTHANDIZA KUPANGA CHIPENA CHOYESA

Kuti mudziwe bwino makina anu komanso mtundu wa ntchito zomwe mungagwire nawo, tikulimbikitsidwa kuti pakhale gawo loyesera monga momwe tafotokozera pansipa:

1.Sankhani chidutswa cha 0.8 mm wandiweyani wachitsulo wofewa kapena pepala la aluminiyamu ndikudula mpaka 335 x 200 mm.
2. Lembani mizere papepala monga momwe zilili pansipa:

3. GwirizanitsaniBenda 1ndi kupanga mlomo m'mphepete mwa workpiece.(Onani

“MULOMO WOPINDIDWA”)

4.Tembenuzani chidutswa choyesera ndikuchiyika pansi pa clampbar, ndikusiya m'mphepete mwanu.Pendekerani clampbar patsogolo ndi mzereBenda 2.Pangani kupindika uku ku 90 °.Chigawo choyesera chiyenera tsopano kuwoneka motere:

…MAYESERO CHIPATA

5.Turn test chidutswa ndi kupangaBend 3, Bend 4ndiBenda 5aliyense mpaka 90 °
6.Kuti amalize mawonekedwewo, chidutswa chotsalira chiyenera kukulungidwa mozungulira zitsulo zozungulira 25 mm.

• Sankhani 280 mm clamp-bar ndikuyiyika, chidutswa choyesera ndi chozungulira pamakina monga tawonera pa "ROLLED EDGE" koyambirira kwa bukuli.
• Gwirani kapamwamba kozungulira ndi dzanja lamanja ndikuyika pre clamping mwa kukanikiza ndi kugwira batani la START ndi dzanja lamanzere.Tsopano gwiritsani ntchito dzanja lanu lamanja kukoka chogwirizira ngati mukupindika wamba (batani la START litha kutulutsidwa).Manga chogwirira ntchito momwe mungathere (pafupifupi 90 °).Bwezeretsani chogwirira ntchito (monga chikusonyezedwera pansi pa "Kupanga Mphepete Yozungulira") ndikukulunganso.Pitirizani mpaka mpukutuwo utatsekedwa.

Mawonekedwe a mayeso tsopano atha.

MABOKSI...

KUPANGA MABOKSI (KUGWIRITSA NTCHITO MA CLAMPBARS AFUPI)

Pali njira zambiri zopangira mabokosi ndi njira zambiri zowapinda.JDCBEND ndiyoyenera kupanga mabokosi, makamaka ovuta, chifukwa cha kusinthasintha kwa kugwiritsa ntchito ma clampbars afupiafupi kupanga mikwingwirima yosalephereka ndi mikungwi yam'mbuyomu.

Mabokosi Osavuta

1.Pangani mipiringidzo iwiri yoyambilira pogwiritsa ntchito clampbar yayitali ngati kupinda kwanthawi zonse.
2.Sankhani imodzi kapena zingapo zazifupi zokhomerera ndi malo monga momwe zasonyezedwera.(Sikofunikira kupanga utali weniweniwo popeza kupindika kudzanyamula mipata osachepera20 mmpakati pa ma clampbars.)

Pamapindika mpaka 70 mm kutalika, ingosankhani chidutswa chachikulu kwambiri chomwe chidzakwanira.Kwa utali wautali pangafunike kugwiritsa ntchito zidutswa zingapo zochepetsera.Ingosankhani clampbar yayitali kwambiri yomwe ingagwirizane, ndiye yayitali kwambiri yomwe ingagwirizane ndi kusiyana kotsalira, ndipo mwina yachitatu, ndikupanga kutalika kofunikira.

Popinda mobwerezabwereza zidutswa za clamp zitha kulumikizidwa kuti apange unit imodzi yokhala ndi utali wofunikira.Kapenanso, ngati mabokosi ali ndi mbali zozama ndipo muli ndi aclampbar yotsekedwa,ndiye zingakhale zofulumira kupanga mabokosiwo mofanana ndi matayala osaya.(Onani gawo lotsatira: TRAYS)

Mabokosi okhala ndi milomo

Mabokosi okhala ndi milomo amatha kupangidwa pogwiritsa ntchito ma clampbars amfupi ngati miyeso imodzi ndiyokulirapo kuposa m'lifupi mwake (98 mm).

1. Pogwiritsa ntchito clampbar yautali, pangani mipiringidzo yanzeru 1, 2, 3, &4.
2.Sankhani clampbar yaifupi (kapena mwina awiri kapena atatu olumikizidwa pamodzi) ndi kutalika kwa milomo-m'lifupi mwake yayifupi kuposa m'lifupi mwa bokosilo (kotero kuti pambuyo pake idzachotsedwa).Pangani mikungwi 5, 6, 7 & 8. Pamene mukupanga mikungwi 6 & 7, samalani ndi kulondolera ngodya.

ma tabu mkati kapena kunja kwa bokosilo, monga momwe mungafunire.

... MABOKSI...

Mabokosi okhala ndi malekezero osiyana

Bokosi lopangidwa ndi mbali zosiyana liri ndi ubwino wambiri:

-Imapulumutsa zinthu ngati bokosi lili ndi mbali zakuya,

-sifuna kutchingira ngodya,

-Kudula konse kumatha kuchitidwa ndi guillotine,

-kupinda konse kungathe kuchitidwa ndi clampbar yautali wamba;

ndi zovuta zina:

- mikwingwirima yambiri iyenera kupangidwa,

-makona ambiri ayenera kulumikizidwa, ndi

-m'mphepete mwazitsulo zambiri ndi zomangira zimawonekera pabokosi lomalizidwa.

Kupanga bokosi lamtunduwu ndikolunjika kutsogolo ndipo clampbar yautali imatha kugwiritsidwa ntchito pamapangidwe onse.

1.Konzani zomwe zikusowekapo monga momwe zilili pansipa.
2.Choyamba kupanga makutu anayi mu workpiece yaikulu.

3.Chotsatira, pangani ma flange 4 pa chidutswa chilichonse.Pazipinda zonse izi, ikani chopendekera chopapatiza cha chidutswa chomaliza pansi pa clampbar.
4.Lowani bokosi limodzi.

 

Mabokosi a flanged okhala ndi ngodya zomveka

Mabokosi owoneka bwino okhala ndi ma flanges akunja ndiosavuta kupanga ngati kutalika ndi m'lifupi ndizokulirapo kuposa kukula kwa clampbar 98 mm.Kupanga mabokosi okhala ndi ma flange akunja kumagwirizana ndikupanga TOP-HAT SECTIONS (zofotokozedwa m'gawo lotsatira - onani Zamkatimu).

4.Konzani chopanda kanthu.
5. Pogwiritsa ntchito clampbar yayitali, pindani 1, 2, 3 & 4.
6.Lowetsani flange pansi pa clampbar kuti mupange pindani 5, kenako pindani 6.
7. Pogwiritsa ntchito zingwe zazifupi zoyenera, malizitsani 7 & 8.

... MABOKSI

Bokosi la Flanged Lokhala ndi Ma Corner Tabs

Popanga bokosi lakunja lokhala ndi ma tabu apakona komanso osagwiritsa ntchito zidutswa zosiyana, ndikofunikira kupanga mapindidwe motsatana bwino.

1.Konzani chopanda kanthu ndi ma tabu angodya okonzedwa monga momwe asonyezedwera.

2.Pamapeto amodzi a clamp bar yautali, pangani makutu onse a tabu "A" mpaka 90. Ndi bwino kuchita izi mwa kuyika tabu pansi pa clampbar.
3.Pamapeto omwewo a clampbar yautali, pangani makutuⁿBⁿ mpaka 45° basi.Chitani izi mwa kuyika mbali ya bokosi, osati pansi pa bokosi, pansi pa clampbar.
4.Kumapeto ena a clampbar yautali, pangani mapiko a flange "C" mpaka 90 °.
5. Pogwiritsa ntchito zingwe zazifupi zoyenera, pindani kwathunthuⁿBⁿku 90.
6.Lowani m'makona.
Kumbukirani kuti pamabokosi akuya zingakhale bwino kupanga bokosilo ndi zidutswa zosiyana.

SLOTTED CLAMPBAR

KUPANGA MATRAY (KUGWIRITSA NTCHITO SLOTTED CLAMPBAR)

Slotted Clampbar, ikaperekedwa, ndi yabwino kupanga matayala osaya ndi mapoto mwachangu komanso molondola.Ubwino wa clampbar yotchinga pamwamba pa zotchingira zazifupi zopangira ma tray ndikuti m'mphepete mwake mumangolumikizana ndi makina onse, ndipo clampbar imadzikweza yokha kuti ithandizire kuyika kapena kuchotsa chogwiriracho.Osachepera, ma clampbars amfupi amatha kugwiritsidwa ntchito kupanga ma tray akuya mopanda malire, ndipo, ndithudi, ndiabwino kupanga mawonekedwe ovuta.

Pogwiritsidwa ntchito, mipatayo imakhala yofanana ndi mipata yomwe yatsala pakati pa zala za bokosi lodziwika bwino & makina opinda.M'lifupi mwa mipatayo ndiye kuti mipata iwiri iliyonse idzakwanira ma tray opitilira kukula kwa 10 mm, ndipo kuchuluka ndi malo omwe mipatayo ndi yoti.zamitundu yonse ya tray, patha kupezeka mipata iwiri yomwe ingagwirizane nayo.(Mikulidwe ya tray yayifupi komanso yayitali kwambiri yomwe clampbar yotsekeka ikhalamo yandandalikidwa pansi pa MFUNDO.)

Kupinda tray yakuya:

1. Pindani mbali ziwiri zoyang'ana zoyambira ndi ma tabo apakona pogwiritsa ntchito clampbar yotsekedwa koma osanyalanyaza kupezeka kwa mipata.Mipata iyi sidzakhala ndi zotsatira zowoneka pazipinda zomalizidwa.
2. Tsopano sankhani mipata iwiri yopinda pakati pa mbali ziwiri zotsalazo.Izi ndizosavuta komanso mwachangu modabwitsa.Ingolani mzere kumanzere kwa thireyi yopangidwa pang'ono ndi kagawo kakang'ono kumanzere ndikuwona ngati pali polowera mbali yakumanja yolowera;ngati sichoncho, tsitsani thireyi mpaka mbali yakumanzere ifike polowera kwina ndikuyesanso.Nthawi zambiri, zimatengera pafupifupi 4 kuyesa kotere kuti mupeze mipata iwiri yoyenera.
3. Pomaliza, ndi m'mphepete mwa thireyi pansi pa clampbar ndi pakati pa mipata iwiri yosankhidwa, pindani mbali zotsalazo.Mbali zomwe zidapangidwa kale zimalowa m'malo osankhidwa pomwe mikwingwirima yomaliza ikamalizidwa.

Ndi utali wa thireyi womwe umakhala wotalika ngati clampbar kungakhale kofunikira kugwiritsa ntchito mbali imodzi ya clampbar m'malo mwa slot.

ZAMBIRI

KUGWIRITSA NTCHITO ZAMBIRI

Zotsalira zam'mbuyo zimakhala zothandiza pamene mapindikidwe ambiri ayenera kupangidwa onse omwe ali pamtunda wofanana kuchokera pamphepete mwa workpiece.Ma backstops atayikidwa molondola nambala iliyonse yopindika imatha kupangidwa popanda kufunikira koyezera kapena kulemba chizindikiro pa workpiece.

Nthawi zambiri ma backstops amatha kugwiritsidwa ntchito ndi bala yomwe imayikidwa pambali pawo kuti apange malo aatali pomwe amalozera m'mphepete mwa chogwiriracho.Palibe bar yapadera yomwe imaperekedwa koma chowonjezera kuchokera pamtengo wopindika chingagwiritsidwe ntchito ngati bar ina yoyenera palibe.

ZINDIKIRANI:Ngati pakufunika kukhazikitsa backstoppansiclampbar, ndiye kuti izi zitha kuchitika pogwiritsa ntchito chingwe cha sheetmetal chofanana ndi makulidwe a workpiece, molumikizana ndi kumbuyo.

KULONDA

KUONA KUKHALA KOMA KWA MAKANI YANU

Malo onse ogwira ntchito a Jdcbend amapangidwa kuti azikhala owongoka komanso osalala mpaka mkati mwa 0.2 mm kutalika konse kwa makinawo.

Zofunikira kwambiri ndizo:

1. kuwongoka kwa malo ogwirira ntchito a mtengo wopindika,
2. kuwongoka kwa nsonga yopindika ya clamp bar, ndi
3. kufanana kwa malo awiriwa.

Malowa amatha kuyang'aniridwa molunjika koma njira ina yabwino yowunikira ndikuwunika momwe zinthu ziliri.Kuchita izi:

1. Tembenukirani mtengo wopindika mpaka 90 ° ndikuigwira pamenepo.(Mtanda ukhoza kutsekedwa pamalowa poyika kolala yotsekera kumbuyo kumbuyo kwa slide pa chogwirira).
2. Yang'anani kusiyana pakati pa m'mphepete mwachitsulo chopindika ndi malo ogwirira ntchito a mtengo wopindika.Pogwiritsa ntchito zowongolera zochepetsera ikani kusiyana kumeneku kufika 1 mm kumapeto kulikonse (gwiritsani ntchito zidutswa zachitsulo, kapena choyezera chomveka).

Onetsetsani kuti kusiyana kuli kofanana njira yonse pa clampbar.Kusiyanasiyana kulikonse kuyenera kukhala mkati mwa ± 0.2 mm.Tliat ndi kusiyana sayenera kupitirira 1.2 mm ndipo sayenera kuchepera 0.8 mm.(Ngati osinthawo sakuwerenga zomwezo kumapeto kulikonse ndiye zikhazikitseninso monga zafotokozedwera pa MAINTENANCE).

Ndemanga:

1. Kuwongoka kwa clampbar monga momwe kumawonekera pamtunda (kuchokera kutsogolo) sikofunikira chifukwa izi zimaphwanyidwa ndi maginito a clamping makina akangotsegulidwa.
2. Kusiyana pakati pa mtengo wopindika ndi thupi la maginito (monga momwe zimawonedwera powonera ndi mtengo wopindika pamalo ake) nthawi zambiri zimakhala pafupifupi 2 mpaka 3 mm.Kusiyana ukuayimbali yogwira ntchito ya makina ndipo sizimakhudza kulondola kwa kupinda.
3. Jdcbend imatha kupanga zopindika zakuthwa muzitsulo zocheperako komanso muzinthu zopanda chitsulo monga aluminiyamu ndi mkuwa.Komabe muzitsulo zolimba zachitsulo ndi zitsulo zosapanga dzimbiri musayembekezere kukwaniritsa khola lakuthwa (onani ndondomeko).
4. Kufanana kwa bend mumageji okhuthala kumatha kupitsidwanso pogwiritsa ntchito zidutswa zachidutswa kuti mudzaze magawo omwe sanagwiritsidwe ntchito pansi pa clampbar.

KUKONZA

NTCHITO NTCHITO

Ngati malo opanda kanthu a makinawo achita dzimbiri, odetsedwa kapena madamu okalamba, amatha kukonzedwanso mosavuta.Ma burrs aliwonse okwezedwa ayenera kuchotsedwa, ndipo pamwamba pake amapakidwa ndi pepala la P200 emery.Pomaliza ikani mankhwala opoperapo odana ndi dzimbiri monga CRC 5.56 kapena RP7.

HINGE LUBRICATION

Ngati chikwatu cha Jdcbend sheetmetal chikugwiritsidwa ntchito mosalekeza, perekani mafuta kapena mafuta mahinji kamodzi pamwezi.Ngati makinawo sagwiritsidwa ntchito mocheperapo, ndiye kuti akhoza kuthiridwa mafuta pafupipafupi.

Mabowo opaka mafuta amaperekedwa muzitsulo ziwiri za mbale yayikulu ya hinge, ndipo chozungulira chozungulira cha block block iyeneranso kukhala ndi mafuta opakapo.

ZOSINTHA

Zosintha zomwe zili kumapeto kwa clampbar yayikulu ndikuwongolera chiwongolero cha makulidwe a chogwirira ntchito pakati pa m'mphepete ndi chipilala chopindika.Zosintha zimayikidwa fakitale kuti zipereke chiwongola dzanja cha 1 mm pomwe chowongolera chikuwonetsa "1".

1. Gwirani mtengo wopindika pa 90.

2.Ikani kachidutswa kakang'ono ka 1 mm sheetmetal kumapeto kulikonse pakati pa nsonga yopindika ndi mtengo wopindika.
3.Kunyalanyaza zizindikiro zowonetsera, sinthani zosinthazo mpaka zidutswa za 1 mm zimangokhala "zodulidwa" mopepuka pakati pa nsonga yopindika ndi mtengo wopindika.
4. Pogwiritsa ntchito fungulo la 3 mm Allen, masulani mosamala grub-screw kuti mumasulire mphete yokhotakhota ya imodzi mwa osintha.Kenako tembenuzani mpheteyo mpaka mzere wosonyeza "1ⁿ.Chitani izi popanda kuzungulira mkati mwa ad juster.Kenako limbitsaninso grub-screw.
5.Bwezerani chosintha china mofananamo.
Mipira yonyamulira yodzaza ndi masika kumunsi kwa zosinthira imatha kumamatira ngati dothi kapena chinyontho chopanga dzimbiri chilowa. Izi zikachitika, wongolerani pokanikizira mpirawo ndikutuluka ndi chida chosamveka kwinaku mukupopera mafuta mumafuta olowera monga CRC. 5.56 kapena RP7.